1. Home
  2. PLC and HMI programming

PLC and HMI programming

New control systems, rewrites of code that has grown out of control, and fault finding on machines that stop for no obvious reason. Seven PLC platforms, one engineer.

MB AutomationSheet 5 of 12
Service
PLC and HMI
Platforms
7 brands
Languages
LD, ST, FBD
Based in
Sydney, NSW

Code your maintenance team can read

Good PLC code is structured, named consistently and commented, so the next person can find a fault at two in the morning without calling us. We write modular code with one block per device or function, keep machine states explicit, and test everything offline before it reaches your site.

Because the same engineer also designs the mechanics and the electrical system, the program is written around how the machine really behaves, not around a drawing.

What is included

  • Control philosophy and functional design specification agreed first
  • Structured text, ladder and function block diagram, whichever suits each task
  • Alarm and operator messages written for operators, not programmers
  • Offline simulation and testing before site
  • Commissioning, fault finding, backups and handover

Platforms we program

Multi vendor experience, so the solution fits your plant rather than the other way around.

Siemens

  • TIA Portal
  • S7-1200 and S7-1500
  • SCL, ladder and FBD
  • WinCC HMI

Rockwell

  • Allen-Bradley
  • RSLogix
  • MicroLogix
  • FactoryTalk View

Beckhoff

  • TwinCAT
  • CX embedded PCs
  • EtherCAT I/O

Omron

  • CX‑Programmer

Schneider

  • PLC and drive integration

Mitsubishi and ABB

  • Control programs and drive integration

Typical PLC jobs

New machine control

Sequences, motion, recipes, alarms and the interface to the safety system.

Logic rewrites

Code that has been patched for years, rebuilt so it can be understood and extended.

Fault finding

Intermittent faults tracked down with logged data and a methodical check of the machine.

Migrations

Obsolete PLCs moved to current platforms, with the I/O and logic mapped across.

Drives and motion

Drives parameterised and integrated, including SEW MOVITRAC, SINAMICS S120 and servo drives.

HMI, SCADA and networks

Screens, alarms and trends in WinCC, FactoryTalk View or Ignition, over PROFINET, EtherNet/IP, Modbus, Profibus or OPC UA.

How a PLC project runs

  1. 01

    Scope and specify

    We agree what the machine must do, the I/O and the network layout in a functional specification before any code is written.

  2. 02

    Write and simulate

    Modular, commented code is written and tested offline, so most problems are found before site.

  3. 03

    Commission

    On site testing, tuning, fault finding and operator training, with safety functions validated.

  4. 04

    Hand over and support

    Commented source, I/O lists, network documentation and backups, with support after go live.

PLC programming questions

Which PLC brands do you program?
Siemens, Rockwell (Allen-Bradley), Beckhoff, Schneider, Omron, Mitsubishi and ABB. We recommend the brand that suits your plant, your spares and your maintenance team, not a single supplier.
Can you take over PLC code that someone else wrote?
Yes. We review the code, document how it works and fix or restructure what needs it. A short handover call with the original author helps when that is possible, but it is not essential.
Can you replace an obsolete PLC, drive or HMI?
Yes. Upgrades and retrofits are a large part of the work. The new system is built and tested offline so the shutdown is as short as possible.
Will my maintenance team be able to read and change the code?
That is the aim. The code is structured, consistently named and commented, and the handover includes the I/O list, the network layout and a backup of every program.
Can you fault find a machine that stops for no obvious reason?
Yes. Intermittent faults are found with data rather than guesswork: logged states, alarms and timing from the PLC, checked against the mechanical and electrical behaviour of the machine.

More questions and answers

Need a PLC programmer in Sydney?

Tell us the machine, the PLC make and model if you know it, and what is going wrong or what you want it to do.